saw filter ACTF8086 847.0 mhz feature s ? low - loss rf filter for mobile systems ? low amplitude ripple ? no matching network required for operation at 50 ? ceramic p ackage for s urface m ounted t echnology ( smt ) ? lead- free production and rohs c omplian t p ackage dimension s ceramic pa ckage: dcc6 c pin configuration 2 input 5 output 1, 3, 4, 6 ground m arking top view, laser marking " act ?: manufacturer?s mark ? f ?: saw filter ? 8086 ?: part number ? ?: terminal 1 ? ?: lot number (the code shown below va ries in a 4 - year cycle) code 1 2 3 4 5 6 7 8 9 10 11 12 2010 n p q r s t u v w x y z 2011 a b c d e f g h i j k m 2012 n p q r s t u v w x y z 2013 a b c d e f g h j k l m
saw filter ACTF8086 847.0 mhz maximum ratings rating value unit input power level p 13. 5 dbm cw ta=85 c life time>10 years 20 dbm cw ta=85 c pass band top frequency test 1000 hours continuously ,electrical characters meet demand 23 dbm cw ta=85 c pass band top frequency test 2 hours continuously ,electrical characters meet demand dc v oltag e v dc 12 v operating t emperature r ange t a -40 ~ + 85 c storage t emperature r ange t stg - 40 ~ +85 c electrical characteristics parameter unit minimum typical maximum center frequency mhz 847 insertion loss (8 32 ~8 62 mhz) db 2 .0 3.0 amplitude var iation(8 32 ~8 62 mhz) db 0 .6 1.2 group delay variation(8 32 ~8 62 mhz) ns 30 50 a bsolute attenuation 10~ 582 mhz db 50 60 582 ~7 22 mhz db 45 55 7 22 ~7 92 mhz db 40 50 7 92 ~ 820 mhz db 33 40 902 ~ 928 mhz db 37 42 928 ~ 1112 mhz db 45 53 1112 ~ 1300 mhz db 43 51 1300 ~ 30 00mhz db 25 30 input/output return loss(8 32 ~8 62 mhz) db 12 14 rf power dbm +2 0 input/output impedance ohm 50 r ohs c ompli an t electrostatic sensitive device
saw filter ACTF8086 847.0 mhz typical frequency response s21 s11
saw filter ACTF8086 847.0 mhz stability c haracteristics test item condition of test 1 mechanical shock (a) drops: 3 times on concrete floor (b) height: 1.0 m 2 vibration resistance (a) frequency of vibration: 10 ~ 55hz (b) amplitude: 1.5 mm (c) directions: x,y and z (d) duration: 2 hou rs 3 moisture resistance (a) condition: 40 c , 90~95% r.h. (b) duration: 96 hours (c) wait 4 hours before measurement 4 climatic sequence (a) + 70 c for 16 hours (b) +55 c for 24 hours, 90~95% r.h. (c) - 25 c for 2 hours (d) +40 c for 24 hours, 90~95% r.h. (e) wait 4 hours before measurement 5 high t emperature e xposure (a) temperature: 70 c (b) duration: 250 hours (c) wait 4 hours before measurement 6 thermal impact (a) +70 c for 30 minutes ? - 25 c for 30 minutes repeated 3 times (b) wait 4 hours before measurement requirements : the saw filer shall remain w ithin the electrical specifications after tests. r emarks ? saw devices should not be used in any type of fluid such as water, oil, organic solvent, etc. ? be certain not to apply voltage exceeding the rated voltage of components. ? do not operate outside the recommended operating temperature range of components. ? sudden change of temperature shall be avoided, deterioration of the characteristics can occur. ? be careful of soldering temperature and duration of components when soldering. ? do not place soldering iron on the body of components. ? be careful not to subject the terminals or leads of components to excessive force. ? saw devices are electrostatic sensitive . p leas e avoid static voltage during operation and storage. ? u ltrasonic cleaning shall be avoided . ultrasonic vibration may cause destruction of components . t est circuit recommended land pattern
saw filter ACTF8086 847.0 mhz recommended soldering profile p acking informati on carrier tape
saw filter ACTF8086 847.0 mhz reel dimensions outer packing type quantity dimension description weight carton box 0.85 carton box 2 0000 1 90190190 1. 80 un it: mm unit: kg a c e a act . all rights reserved. note: 1. the specifications of this device are subject to change or obsolescence without notice. 2. typically, equipment utilizing this device requires emissions testing and government approval, which is the responsibility of the equipment manufacturer. 3. our liability is only assumed for the surface acoustic wave (saw) component(s) per se, not for applications, processes and circuits implemented within components or assemblies.
|
